Victron

The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The BatteryProtect is not designed for reverse currents from charging sources.   Features 12/24V auto ranging The BatteryProtect automatically detects system voltage. Programming made easy The BatteryProtect can be set to engage / disengage at several different voltages. The seven segment display will indicate which setting has been chosen. A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Ultra low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information. Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V. Ignition proof No relays but MOSFET switches, and therefore no sparks. Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the alarm has been activated. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BPR000065400 Voltage 12/24 Peak Current (During 30 Seconds) 250A Max. Continuous Load Current 65A Connection M6 IP Rating Electronics: IP67 (potted) Connections: IP00 Dimensions (Including Terminals) H40 x W48 x D106mm Weight (kg) 0.2 Warranty 5 Years

Read more less

The MPPT VE.Can SmartSolar charger uses the latest and fastest technology to convert energy from a solar array into energy that optimally charges a battery banks. The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulphated or otherwise damaged.   Features Control Your Charger Remotely The MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data.  Daisy Chain Additional Units The VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy chained” to each other with a single RJ45 cable between the individual units. When connected to each other, all individual VE.Can SmartSolar chargers, will synchronise their charge stages. They can also send their data, via a single cable, to a GX monitoring device.  Remote Monitoring and Control If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your solar charger(s). For remote installations – even when there is no internet connection nearby – you may be able to monitor your MPPT by connecting the GlobalLink 520. Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the powervoltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more SmartSolar Charge Controllers. VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Fully discharged battery recovery function Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function. VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can, and up to 10 units with Bluetooth Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC115070411 GTIN 8719076050322 Battery Voltage 12/24/48V Auto Select (36V: manual) Rated Charge Current 70A Nominal PV Power, 12V 1000W Nominal PV Power, 24V 2000W Max. PV Short Circuit Current 50A Maximum PV Open Circuit Voltage 150V absolute maximum coldest conditions, 145V start-up and operating maximum Efficiency 98% Charge Algorithm multi-stage adaptive (eight preprogrammed algorithms) or user defined algorithm Data Communication Port VE.Can, VE.Direct and Bluetooth IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H185 x W250 x D95mm Weight 3Kg Warranty 5 Years

Read more less

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life.   Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30 % compared to PWM charge controllers and by up to 10 % compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98 %. Flexible charge algorithm Fully programmable charge algorithm, and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor and optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature (and current, in case of a BMV-712 or a SmartShunt) to one or more BlueSolar Charge Controllers. (VE.Direct Bluetooth Smart dongle needed) Real-time data display options Color Control GX or other GX devices: see the Venus documents on our website. A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC010070200 GTIN 8719076025511 Battery Voltage 12/24/48V Auto Select (software tool needed to select 36V) Rated Charge Current 70A Nominal PV Power, 12V 1000W Nominal PV Power, 24V 2000W Max. PV Short Circuit Current 50A Maximum PV Open Circuit Voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H185 x W250 x D95mm Weight 3Kg Warranty 5 Years

Read more less

Liquid crystal display For status monitoring and set-up Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable. Day/night timing of the load output This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs Maximum current (both outputs combined): 2A CLICK HERE FOR SPEC SHEET   Brand Victron Energy Manufacturer Part Number SCC010020050 GTIN 8719076046202 Battery Voltage 12/24 V automatic system voltage detection Rated Charge Current 20A Maximum Solar Voltage 28V / 55V Load Output Manual control + low voltage disconnect + timer Grounding Common positive IP Rating IP20 Dimensions H96 x W169 x D36mm Weight 0.15Kg Warranty 5 Years

Read more less

Features Load output with low battery voltage disconnect function. Lighting control function, one timer only.  Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.  Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC010020020 GTIN 8719076025351 Battery Voltage 12/24V with automatic system voltage detection Rated Charge Current 20A Maximum Solar Voltage 28V / 55V Grounding Common positive IP Rating IP20 Dimensions H70 x W133 x D33.5mm Weight 0.15Kg Warranty 5 Years

Read more less

Indispensable in professional marine energy systems. It prevents electrolytic corrosion and above all serves as a device to guarantee a safe electric system. Toroidal wound technology for quietness and high efficiency. Soft start circuitry will ensure that the shore circuit breaker will not trip when plugged in.   Features Safety and prevention of galvanic corrosion The Isolation Transformer eliminates any electrical continuity between AC shore power and the boat. It is essential for safety and eliminates the need for galvanic isolators and polarity alarms. Safety is taken for granted in case of a normal on-shore installation. A fuse will blow or a GFCI (Ground Fault Current Interrupter) will trip in case of a short circuit or current leakage to ground. Connecting the ground wire of the shore-side supply to the metal parts of the boat will result in galvanic corrosion (see below). Bringing only the live and neutral wire on board results in an unsafe situation because GFCIs will not work nor will a fuse blow in case of a short circuit to a metal part on the boat. Galvanic corrosion occurs when two dissimilar metals in electrical contact are simultaneously exposed to an electrically conducting fluid. Seawater and, to a lesser extent, fresh water are such fluids. In general, the more active alloy of the couple corrodes preferentially while the less active (more noble) material is cathodically protected. The rate of galvanic corrosion is a function of several variables including area ratios, conductivity of the fluid, temperature, nature of the materials, etc. It is a misunderstanding that galvanic corrosion occurs only in metal and aluminium hulls. In fact it can occur on any boat as soon as a metallic part (the shaft and propeller) is in contact with water. Galvanic corrosion will quickly dissolve your sacrificial anodes, and attack the shaft, propeller and other metal parts in contact with water as soon as the boat is connected to the shore-side supply. It might therefore be tempting not to connect the ground conductor: this is however extremely dangerous because GFCIs will not work nor will a fuse blow in case of a short circuit to a metal part on the boat. The best solution to avoid galvanic corrosion and at the same time prevent any unsafe situation is to install an Isolation Transformer to connect to the shore-side supply. The Isolation Transformer eliminates any electrical continuity between shore power and the boat. The shore power is fed to the primary side of the transformer and the ship is connected to the secondary. The Isolation Transformer completely isolates the boat from the shore ground. By connecting all metal parts to the neutral output on the secondary side of the transformer, a GFCI will trip or a fuse will blow in case of a short circuit. Soft start is a standard feature of a Victron Energy isolation transformer. It will prevent the shore power fuse from blowing due to the inrush current of the transformer, which would otherwise occur. It is also recommended, for optimal safety, to connect the secondary neutral of the transformer to ground when the boat is out of the water. 3600 Watt Auto 115/230 V This model will automatically switch to 115 V or 230 V supply, depending on input voltage. Supply 88 V – 130 V: switches to 115 V supply Supply 185 – 250 V: switches to 230 V supply range. Note: The AC input voltage is raised by 1:1.05 ratio at the AC output.   CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ITR050362041 Input Automatic 115/230 V switching Output 115 or 230 V Frequency 50/60 Hz Rating 32 / 16 A Soft Start Yes Transformer Type Toroidal (low noise, low weight) Input Circuit Breaker Yes Protection Category IP21 Dimensions H362 x W258 x D218mm Weight (kg) 24 Warranty 5 Years

Read more less

The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to 55°C with a full rated output up to 40°C.   Features Bluetooth Smart enabled Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available. Fully programmable Battery charge algorithm (configurable) or fixed output. Smart alternator compatibility: engine running detection mechanism. Adaptive 3-stage charge algorithm: bulk – absorption – float For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.  For lithium batteries absorption time is fixed, default 2 hours. Alternatively, a fixed output voltage can be chosen. Remote on-off A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example). All models are short circuit proof and can be paralleled to increase output current An unlimited number of units can be connected in parallel. High temperature protected The output current will reduce at high ambient temperature. IP43 protection When installed with the screw terminals oriented downwards. Screw terminals No special tools needed for installation. Input fuse (not replaceable)  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI241224120 Input Voltage Range 16-35V Output Voltage Adjust Range 10-15V Nominal Output Voltage 12.2V Cont. Output Power at 25°C (W) 300W Cont. Output Power at 40°C (W) 240W Under Voltage Shutdown 14V Under Voltage Restart 15V DC Connection Screw Terminals Efficiency 88% Protection Category IP43 Dimensions H130 x W186 x D70mm Weight (kg) 1.3 Warranty 5 Years

Read more less

Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).  Adjustable output voltage: can also be used as a battery chargerFor example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.  All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.  IP43 protectionWhen installed with the screw terminals oriented downwards.  Screw terminalsNo special tools needed for installation. Input fuseOn 12V and 24V input models only.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI121222110 Input Voltage Range 8-17V Under Voltage Shutdown 7V Under Voltage Restart 7.5V Nominal Output Voltage 12.2V Output Voltage Adjust Range 10-15V Short Circuit Output Current 40A Cont. Output Power at 25°C 280W DC Connection Screw Terminals Protection Category IP43 Dimensions H130 x W186 x D70 mm Weight (kg) 1.3 Warranty 5 Years

Read more less

The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to 55°C with a full rated output up to 40°C.   Features Bluetooth Smart enabled Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available. Fully programmable Battery charge algorithm (configurable) or fixed output. Smart alternator compatibility: engine running detection mechanism. Adaptive 3-stage charge algorithm: bulk – absorption – float For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.  For lithium batteries absorption time is fixed, default 2 hours. Alternatively, a fixed output voltage can be chosen. Remote on-off A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example). All models are short circuit proof and can be paralleled to increase output current An unlimited number of units can be connected in parallel. High temperature protected The output current will reduce at high ambient temperature. IP43 protection When installed with the screw terminals oriented downwards. Screw terminals No special tools needed for installation. Input fuse (not replaceable)  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI121236140 Input voltage range 10-17V Under voltage shut down 7V Under voltage restart 7.5V Nominal output voltage 12.2V Output voltage adjust range 10-15V Cont. output current at nominal output voltage and 40°C 30A Short circuit output current 60A Cont. output power at 25°C 430W Cont. output power at 40°C 360W Efficiency 87% DC connection Screw Terminals IP Rating IP43 Dimensions H130 x W186 x D80mm Weight 1.8Kg Warranty 5 Years

Read more less

Remote on-off connector The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual). All models with adjustable output can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models with adjustable output can be paralleled to increase output current Up to five units can be connected in parallel. Easy to install Delivery includes four Insulated Fastons Female Crimp 6.3mm (eight Fastons in case of the Orion 24/12-40). Low power models: please see Orion-Tr series  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI122410020 Input Voltage Range 9-18V Output Voltage Adjustable 20-30V F set 26.4V Under Voltage Shutdown 8V Under Voltage Restart 10V Continuous Output Current 10A DC Connection Faston tabs 6.3 mm Remote on-off No Galvanic Isolation No Can be connected in parallel Yes Protection Category IP20 Dimensions H45 x W90 x D125mm Weight (kg) 0.4 Warranty 5 Years

Read more less

    A modular DC bus bar, used to connect batteries to the Lynx DC distribution system.   The lynx power in module is used to connect batteries via an external fuse. It can be useful if you have multiple parallel strings. Due to the extremely high short circuit current potential of most battery banks, it is suggested to use an external fuse system with an appropriate fault current interruption rating (such as an NH HRC). The Power In contains a negative and positive DC bus-bar with M8 bolts in which to connect batteries cables. It can take cables up to 22 mm in diameter through the bottom entry guides, and no limit via the two side connections.  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number LYN020102000 Dimensions H282 x W172 x D78mm Weight (kg) 2.1 Warranty 5 Years

Read more less

      The Victron Transfer Switch is designed to take over automatic switching between different power sources: between an generator and the shore, or between an inverter and a generator, or between an inverter and the shore. The Transfer Switch has two inputs and one output and automatically transfer the available AC power to output. It can be used with any Victron Energy inverter, dependent on capacity.   Brand Victron Energy Manufacturer Part Number COS230103100 Warranty 5 Years

Read more less

MEGA-fuse 125A/58V for 48V products (1 pc)   Brand Victron Energy Manufacturer Part Number CIP137125010 Warranty 5 Years Appr. Voltage Drop 90 mV Cold Resistance 0.4

Read more less

Shunt 1000A/50mV-0,5 / 2xM10 Brand Victron Energy Manufacturer Part Number SHU102050200 Warranty 5 Years

Read more less

Solar connector pair MC4, 1x Male/1x Female Brand Victron Energy Manufacturer Part Number SCA520300000 Warranty 5 Years

Read more less

High stock levels available on all panels, please contact us via live chat for up-to-date stock before purchase, as stock levels are subject to change. Alternatively, you can email or call us. Low voltage-temperature coefficient enhances high-temperature operation. Exceptional low-light performance and high sensitivity to light across the entire solar spectrum. 25-Year limited warranty on power output and performance. 5-Year limited warranty on materials and workmanship. Sealed, waterproof, multi-functional junction box gives high level of safety. High performance bypass diodes minimize the power drop caused by shade. Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation. A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems. Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance. High power models with pre-wired quick-connect system with MC4 (PV-ST01) connectors.  CLICK HERE FOR SPEC SHEETS Brand Victron Energy Manufacturer Part Number SPM040901200 Voltage 12 Nominal Power (W) 90 Number of cells in series 36 Maximun System Voltage 1000 Dimensions L780 x W668 x D30mm Weight (kg) 6.1 Warranty 5 Years Cell Type Monocrystalline

Read more less

All Batteries are Made By Leading Manufacturers The AGM range has very low internal resistance making them particularly suitable for high current discharge applications such as for inverters, thrusters and winches.  VRLA AGM: design life 7-10 years   Features VRLA technology VRLA stands for Valve Regulated Lead Acid, which means that the batteries are sealed. Gas will escape through the safety valves only in case of overcharging or cell failure. VRLA batteries are maintenance free for life. Sealed (VRLA) AGM Batteries AGM stands for Absorbent Glass Mat. In these batteries the electrolyte is absorbed into a glass-fibre mat between the plates by capillary action. As explained in our book ‘Energy Unlimited’, AGM batteries are more suitable for short-time delivery of high currents than gel batteries. Low Self-Discharge Because of the use of lead calcium grids and high purity materials, Victron VRLA batteries can be stored during long periods of time without recharge. The rate of self-discharge is less than 2% per month at 20°C. The self-discharge doubles for every increase in temperature by 10°C. Victron VRLA batteries can therefore be stored for up to a year without recharging, if kept under cool conditions. Exceptional Deep Discharge Recovery Victron VRLA batteries have exceptional discharge recovery, even after deep or prolonged discharge. Nevertheless repeatedly deep and prolonged discharge has a very negative effect on the service life of all lead acid batteries, Victron batteries are no exception. Battery Discharging Characteristics The rated capacity of Victron AGM and Gel Deep Cycle batteries refers to 20 hour discharge, in other words: a discharge current of 0,05 C. The rated capacity of Victron Tubular Plate Long Life batteries refers to 10 hours discharge. The effective capacity decreases with increasing discharge current (see table 1). Please note that the capacity reduction will be even faster in case of a constant power load, such as an inverter.  All Prices Include VAT Click Here For Spec Sheet Brand Victron Energy Manufacturer Part Number BAT412151085 GTIN 8719076037040 Voltage 12V Battery Capacity (C20) 165Ah Cold Cranking 600CCA Terminal Type M8 Terminal Layout Left Hand Positive Dimensions (Including Terminals) L485 x W172 x H240mm Weight 47Kg Warranty 2 Years Country of Manufacture Vietnam Battery Technology AGM Battery Application Dual Purpose      

Read more less

All Batteries are Made By Leading Manufacturers The AGM range has very low internal resistance making them particularly suitable for high current discharge applications such as for inverters, thrusters and winches.  VRLA AGM: design life 7-10 years   Features VRLA technology VRLA stands for Valve Regulated Lead Acid, which means that the batteries are sealed. Gas will escape through the safety valves only in case of overcharging or cell failure. VRLA batteries are maintenance free for life. Sealed (VRLA) AGM Batteries AGM stands for Absorbent Glass Mat. In these batteries the electrolyte is absorbed into a glass-fibre mat between the plates by capillary action. As explained in our book ‘Energy Unlimited’, AGM batteries are more suitable for short-time delivery of high currents than gel batteries. Low Self-Discharge Because of the use of lead calcium grids and high purity materials, Victron VRLA batteries can be stored during long periods of time without recharge. The rate of self-discharge is less than 2% per month at 20°C. The self-discharge doubles for every increase in temperature by 10°C. Victron VRLA batteries can therefore be stored for up to a year without recharging, if kept under cool conditions. Exceptional Deep Discharge Recovery Victron VRLA batteries have exceptional discharge recovery, even after deep or prolonged discharge. Nevertheless repeatedly deep and prolonged discharge has a very negative effect on the service life of all lead acid batteries, Victron batteries are no exception. Battery Discharging Characteristics The rated capacity of Victron AGM and Gel Deep Cycle batteries refers to 20 hour discharge, in other words: a discharge current of 0,05 C. The rated capacity of Victron Tubular Plate Long Life batteries refers to 10 hours discharge. The effective capacity decreases with increasing discharge current (see table 1). Please note that the capacity reduction will be even faster in case of a constant power load, such as an inverter.  All Prices Include VAT Click Here For Spec Sheet Brand Victron Energy Voltage 12 Volts Technology AGM Capacity 110 Ah Length 330 mm Width 171 mm Height inc. terms 220 mm Weight 32 KG    2 YEAR WARRANTY  

Read more less

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life. The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulphated or otherwise damaged.   Features Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices Ultrafast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. The full output current up to 40°C (104°F). Flexible charge algorithm Fully programmable charge algorithm (see the software page on Victron), and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Optional external battery voltage and temperature sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers. Fully discharged battery recovery function Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function. Brand Victron Energy Manufacturer Part Number SCC110050210 Battery Voltage 12/24V Auto Select Rated Charge Current 50A Nominal PV Power, 12V 700W Nominal PV Power, 24V 1400W Max. PV Short Circuit Current 60A Maximum PV Open Circuit Voltage 100V Efficiency 98% Charge Algorithm Multi-stage adaptive Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H130 x W186 x D70mm Weight (kg) 1.3 Warranty 5 Years   CLICK HERE FOR SPEC SHEETS

Read more less

Victron Chargers The Blue Smart IP65 Charger is the new professional battery charger with built-in bluetooth. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans.  Benefits: The battery is charged, smartly… to perfect condition The seven-step charging algorithm gets the best out of your battery. The charger gives the battery the power it needs, maintains its health, ensures better performance… and a longer life. Recovery of deeply-discharged ‘dead’ batteries Unlike other brands, the Blue Smart IP65 Charger will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals. Connect the battery with ease The charger comes with both crocodile clips and M8 eyelets – making it easy to connect to the battery. If you wish, you can leave it permanently connected. Check the status of your battery remotely The Blue Smart IP65 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app.   Features Water, dust and chemical resistant Seven step smart charge algorithm Recovery of fully discharged ‘dead’ batteries Automatic power supply function Severe cold performance: down to -30°C Several other battery life enhancing features Low power mode to charge smaller batteries Li-ion battery mode Setup and configure, readout of voltage and current by Bluetooth Smart   Brand Victron Energy Manufacturer Part Number BPC121531024R Voltage (V) 12 Charger Amps 15 Efficiency 94% Outputs 1 Plug Type UK IP Rating IP65 Dimensions H60 x W105 x D190mm Weight (kg) 0.9 Warranty 5 Years   CLICK HERE FOR SPEC SHEETS

Read more less

Victron Chargers The Blue Smart IP65 Charger is the new professional battery charger with built-in bluetooth. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans.  Benefits: The battery is charged, smartly… to perfect condition The seven-step charging algorithm gets the best out of your battery. The charger gives the battery the power it needs, maintains its health, ensures better performance… and a longer life. Recovery of deeply-discharged ‘dead’ batteries Unlike other brands, the Blue Smart IP65 Charger will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals. Connect the battery with ease The charger comes with both crocodile clips and M8 eyelets – making it easy to connect to the battery. If you wish, you can leave it permanently connected. Check the status of your battery remotely The Blue Smart IP65 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app.   Features Water, dust and chemical resistant Seven step smart charge algorithm Recovery of fully discharged ‘dead’ batteries Automatic power supply function Severe cold performance: down to -30°C Several other battery life enhancing features Low power mode to charge smaller batteries Li-ion battery mode Setup and configure, readout of voltage and current by Bluetooth Smart   Brand Victron Energy Manufacturer Part Number BPC121031024R Voltage (V) 12 Charger Amps 10 Efficiency 945 Outputs 1 Plug Type UK IP Rating IP65 Dimensions H60 x W105 x D190mm Weight (kg) 0.9 Warranty 5 Years   CLICK HERE FOR SPEC SHEETS

Read more less

The Blue Smart IP65 Charger 6V/12V-1.1 is the new professional battery charger with built-in Bluetooth. The Blue Smart IP65s Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans.   Features of the Blue Smart IP65 Charger 6V/12V-1.1 The battery is charged, smartly… to perfect condition The seven-step charging algorithm gets the best out of your battery. The charger gives the battery the power it needs, maintains its health, ensures better performance… and a longer life.   Recovery of deeply-discharged ‘dead’ batteries Unlike other brands, the Blue Smart IP65 Charger 6V/12V-1.1will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals.   ReconditioningA lead-acid battery that has been insufficiently charged or has been left discharged during days or weeks will deteriorate due to sulfation. If caught in time, sulfation can sometimes be partially reversed by charging the battery with low current up to a higher voltage.   Connect the battery with ease The charger comes with both crocodile clips and M8 eyelets – making it easy to connect to the battery. If you wish, you can leave it permanently connected.   Brand Victron Energy Manufacturer Part Number BPC120134024R gtin 8719076055532 Voltage 6/12V Charge Current 1.1A Input Voltage 230V Protection Category IP65 Efficiency 82% Bluetooth Enabled Yes Plug Type UK Dimensions H38 x W64 x D153mm Weight 0.4Kg Warranty 5 Years Country of Manufacture India

Read more less

Cerbo-S GX BPP900450120  This all-new communication-centre allows you to always have perfect control over your system from wherever you are and maximises its performance. Simply connect through the Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch, a MFD or the VictronConnect App thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way. Instantly monitor the battery state of charge, power consumption, power harvest from PV, generator, and mains, or check tank levels and temperature measurements. Easily control the shore power input current limit, (auto)start/stop generator(s) or change any setting to optimise the system. Follow up on alerts, perform diagnostic checks and resolve challenges remotely. The Cerbo GX turns any power challenge into an effortless experience. The Cerbo GX maximises the performance of your systems components in real-time and keeps them in perfect tune. With its Dual Core Processor and the addition of an extra CAN-bus port you can now support even bigger systems; closely follow managed (lithium) batteries while the second port can support up to 25 simultaneously connected VE.Can solar chargers. The new NMEA 2000-out support has the GX easily integrated into any boats network. Four tank- and four temperature ports as well as 3 VE.Direct ports, 3 USB ports, 4 digital inputs and 2 relays allow you to expand control to a new level. Maximising systems performance was never this easy. The new (optional) GX Touch display allows you to have an instant overview of your system and adjust settings in the blink of an eye. Its super slim 5 or 7 inch waterproof design, top-mountable setup and its simple installation bring a lot of flexibility when creating a crisp and clean dashboard. The Cerbo GX is now optimised to more than meet the standards of installer professionals. The device is easily mountable on a DIN-Rail and its separate touchscreen can now be bolted on top of a dashboard, eliminating the need to create perfect cut-outs (like with the Color Control GX) and is connected through just one cable, taking away the hassle of having to bring many wires to a dashboard. Its new Bluetooth feature enables a quick connection and configuration via our VictronConnect app. The Cerbo GX serves endless purposes, extending perfect control to the most diverse applications. For solutions including generators, such as Marine, or Off-grid & Backup, it will auto-start/stop your generator, or delays ignition until the end of ‘quiet’ periods. For Energy Storage Systems it keeps backup batteries at 100%, kicks-in during power-cuts and diverts excess (solar) power to self-consumption, saving you money. For RV and Emergency vehicles it keeps vital systems function flawlessly. But that’s just to name a few…   Brand Victron Energy Manufacturer Part Number BPP900450120 gtin 8719076058847 Dimensions H78 x W154 x D48mm Warranty 5 Years Country of Manufacture Malaysia

Read more less

The SmartShunt IP65 500A is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more. Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor especially for systems where battery monitoring is needed but less wiring and clutter is wanted.The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor.   Differences compared to BMV-712 Battery Monitor– No programmable visual and audible alarm– No programmable relay Why should I monitor my battery with the SmartShunt IP65 500A?Batteries are used in a wide variety of applications, mostly to store energy for later use. But how much energy is stored in the battery? No one can tell by just looking at it. The service life of batteries depends on many factors. Battery life may be shortened by under-charging, over-charging, excessively deep discharges, excessive charge or discharge currents, and by high ambient temperature. Monitoring the battery with a battery monitor will give important feedback to the user so that remedial measures can be taken when necessary. Doing this will extend battery life and the battery monitor will quickly pay for itself.   Brand Victron Energy Manufacturer Part Number SHU065150050 gtin 8719076057895 Protection Category IP65 Bluetooth Enabled Yes Dimensions H46 x W120 x D54mm Warranty 5 Years Country of Manufacture India

Read more less

All Batteries are Made By Leading Manufacturers The GEL model range offers best deep cycle durability and overall longer life. The use of high purity materials and lead calcium grids ensure that for both AGM and GEL products have particularly low self-discharge so that they will not go flat during long periods without charge. Both ranges are supplied with M8 drilled, flat copper terminals ensuring best possible connection contact and eliminating the need for battery terminals. The batteries are compliant with both CE and UL specifications in ABS fireproof containers and come with Victron’s 2 year world-wide warranty. VRLA GEL: design life 12 years   Features VRLA technology VRLA stands for Valve Regulated Lead Acid, which means that the batteries are sealed. Gas will escape through the safety valves only in case of overcharging or cell failure. VRLA batteries are maintenance free for life.   Sealed (VRLA) GEL Batteries Here the electrolyte is immobilized as gel. Gel batteries in general have a longer service life and better cycle capacity than AGM batteries.   Low Self-Discharge Because of the use of lead calcium grids and high purity materials, Victron VRLA batteries can be stored during long periods of time without recharge. The rate of self-discharge is less than 2% per month at 20°C. The self-discharge doubles for every increase in temperature by 10°C. Victron VRLA batteries can therefore be stored for up to a year without recharging, if kept under cool conditions.   Exceptional Deep Discharge Recovery Victron VRLA batteries have exceptional discharge recovery, even after deep or prolonged discharge. Nevertheless repeatedly deep and prolonged discharge has a very negative effect on the service life of all lead acid batteries, Victron batteries are no exception.   Battery Discharging Characteristics The rated capacity of Victron AGM and Gel Deep Cycle batteries refers to 20 hour discharge, in other words: a discharge current of 0,05 C. The rated capacity of Victron Tubular Plate Long Life batteries refers to 10 hours discharge. The effective capacity decreases with increasing discharge current (see table 1). Please note that the capacity reduction will be even faster in case of a constant power load, such as an inverter.  All Prices Include VAT Click Here For Spec Sheet Brand Victron Energy Manufacturer Part Number BAT412101104 GTIN 8719076036982 Voltage 12V Battery Capacity (C20) 110Ah Cold Cranking 450CCA Terminal Type M8 Terminal Layout Left Hand Positive Dimensions (Including Terminals) L330 x W171 x H220mm Weight 33Kg Warranty 2 Years Country of Manufacture Vietnam Battery Technology Gel Battery Application Dual Purpose      

Read more less

All Batteries are Made By Leading Manufacturers The AGM range has very low internal resistance making them particularly suitable for high current discharge applications such as for inverters, thrusters and winches.  VRLA AGM: design life 7-10 years   Features VRLA technology VRLA stands for Valve Regulated Lead Acid, which means that the batteries are sealed. Gas will escape through the safety valves only in case of overcharging or cell failure. VRLA batteries are maintenance free for life. Sealed (VRLA) AGM Batteries AGM stands for Absorbent Glass Mat. In these batteries the electrolyte is absorbed into a glass-fibre mat between the plates by capillary action. As explained in our book ‘Energy Unlimited’, AGM batteries are more suitable for short-time delivery of high currents than gel batteries. Low Self-Discharge Because of the use of lead calcium grids and high purity materials, Victron VRLA batteries can be stored during long periods of time without recharge. The rate of self-discharge is less than 2% per month at 20°C. The self-discharge doubles for every increase in temperature by 10°C. Victron VRLA batteries can therefore be stored for up to a year without recharging, if kept under cool conditions. Exceptional Deep Discharge Recovery Victron VRLA batteries have exceptional discharge recovery, even after deep or prolonged discharge. Nevertheless repeatedly deep and prolonged discharge has a very negative effect on the service life of all lead acid batteries, Victron batteries are no exception. Battery Discharging Characteristics The rated capacity of Victron AGM and Gel Deep Cycle batteries refers to 20 hour discharge, in other words: a discharge current of 0,05 C. The rated capacity of Victron Tubular Plate Long Life batteries refers to 10 hours discharge. The effective capacity decreases with increasing discharge current (see table 1). Please note that the capacity reduction will be even faster in case of a constant power load, such as an inverter.  All Prices Include VAT Click Here For Spec Sheet Brand Victron Energy Manufacturer Part Number BAT412550084 GTIN 8719076037125 Voltage 12V Battery Capacity (C20) 60Ah Cold Cranking 280CCA Terminal Type M8 Terminal Layout Left Hand Positive Dimensions (Including Terminals) L229 x W138 x H227mm Weight 20Kg Warranty 2 Years Country of Manufacture Vietnam Battery Technology AGM Battery Application Dual Purpose  

Read more less

 The Color Control GX is the communication-centre of your installation. It offers at-a-glance live information, and lets you control all products connected to it. Full system control is gained – almost anywhere in the world – by accessing your Color Control GX using our free-to-use Victron Remote Management Portal Intuitive system overview – all you need to know At a single touch, Color Control GX provides an instant overview of your system: battery state of charge; present power consumption; power harvest from PV; power provision from mains/generator. The full power of Victron Remote Management Victron Remote Management (VRM) provides you with full access to the very extensive controls and settings of all system-components which are connected to either your CCGX or Venus GX. It allows remote user and installer login – from anywhere, at anytime. This powerful application also provides for hassle-free diagnostic checks and analysis of archived information. Automatic Generator start/stop The Color Control GX can be programmed to auto-start your generator – triggered by low-voltage; high-demand; or battery state of charge. It can be further tailored to delay ignition until the end of ‘quiet’ periods – avoiding accidental nuisance at dead of night. Remote Console – control everything from anywhere… A Remote Console feature is available. It’s like carrying the front face of your CCGX control panel around on your phone, or other device.  Energy Storage Systems – 24 hour Monitoring The Color Control GX manages Energy Storage Systems. It keeps back-up batteries at 100% ; kicks-in during power-cuts; and diverts excess (solar) power to self-consumption – saving you money. For examples and more detailed information see the ESS (Energy Storage System) manual. Remotely monitor your boat or motorhome electrics Planning a trip? Remote monitoring of your Color Control GX allows you to make sure your boat or motorhome are ready to go. Color Control GX also allows you to talk to connected equipment from other manufacturers.  CLICK HERE FOR SPEC SHEET   Brand Victron Energy Manufacturer Part Number BPP010300100R Power Supply Voltage Range 8-70 V DC Dimensions H130 x W120 x D28mm Weight (kg) 0.3 Warranty 5 Years

Read more less

  The SuperPack batteries are extremely easy to install, not needing any additional components.The internal switch will disconnect the battery in case of over discharge, over charge or high temperature. The batteries can be connected in parallel. Series connection is not allowed.    Features Integrated BMS and safety switch The SuperPack batteries are extremely easy to install, needing no additional components. The internal switch will disconnect the battery in case of over discharge, over charge or high temperature. Abuse proof A lead-acid battery will fail prematurely due to sulfation: If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged). If it is left partially charged or worse, fully discharged. A Lithium-Ion battery does not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of Li-ion compared to lead-acid. The SuperPack batteries will cut-off the charge or discharge current when the maximum ratings are exceeded. Efficient In several applications (especially off-grid solar), energy efficiency can be of crucial importance. The round-trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average lead-acid battery is 80%. The round-trip energy efficiency of a Li-ion battery is 92%. The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy are required (battery operating in 70% to 100% charged state). In contrast, a Li-ion battery will still achieve 90% efficiency even under shallow discharge conditions. Can be connected in parallel The batteries can be connected in parallel. Series connection is not allowed. Use in upright position only. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BAT512110710 GTIN 8719076053019 Voltage 12.8 Capacity (C20) 100 Terminal Type M8 Terminal Layout LH+ Dimensions (Including Terminals) H220 x W330 x D172mm Weight 14Kg Warranty 3 Years Battery Technology Lithium

Read more less

The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to 55°C with a full rated output up to 40°C.   Features Bluetooth Smart enabled Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available. Fully programmable Battery charge algorithm (configurable) or fixed output. Smart alternator compatibility: engine running detection mechanism. Adaptive 3-stage charge algorithm: bulk – absorption – float For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.  For lithium batteries absorption time is fixed, default 2 hours. Alternatively, a fixed output voltage can be chosen. Remote on-off A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example). All models are short circuit proof and can be paralleled to increase output current An unlimited number of units can be connected in parallel. High temperature protected The output current will reduce at high ambient temperature. IP43 protection When installed with the screw terminals oriented downwards. Screw terminals No special tools needed for installation. Input fuse (not replaceable)  PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI121222120 GTIN 8719076046066 Input Voltage Range 8-17V Under voltage shut down 7V Under Voltage Restart 7.5V Nominal Output Voltage 12.2V Output Voltage Adjust Range 10-15V Cont. output current at nominal output voltage and 40°C 18A Short Circuit Output Current 40A Cont. Output Power at 25°C 280W Cont. output power at 40°C 220W Efficiency 87% DC Connection Screw Terminals IP Rating IP43 Dimensions H130 x W186 x D70mm Weight 1.3Kg Warranty 5 Years

Read more less

The Phoenix Inverter Smart is an efficient and reliable inverter. Built on our proven and field tested Phoenix inverter platform, it now comes with a new slimmer design and full metal casing. Models are available in 1600VA, 2000VA and 3000VA for 12, 24 or 48V systems.It’s powerful enough to supply most common plug in appliances in your car, boat, caravan or home. A toroidal transformer provides a high peak power surge capacity, stable voltage, frequency and high quality sine-wave. Installation is simpler than ever before with terminals now more accessible for the installer, enabling a more professional finish.   Features Bluetooth built-in: fully configurable with a tablet or smartphone Low battery voltage alarm Low battery voltage cut-off and restart levels Dynamic cut-off: load dependent cut-off level Output voltage: 210 – 245V Frequency: 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Alarm relay Monitoring: In- and output voltage, load and alarms VE.Direct communication port The VE.Direct port can be connected to a computer (VE.Direct to USB interface cable needed) to configure and monitor the same parameters. Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value. Once in standby the inverter will switch on for a short period every 2,5 seconds (adjustable). If the load exceeds the preset level, the inverter will remain on. Remote on/off A remote on/off switch or relay contact can be connected to a two pole connector. Alternatively, the H terminal (left) of the two pole connector can be switched to battery plus, or the L terminal (right) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example). To transfer the load to another AC source: the automatic transfer switch For our low power inverters we recommend our Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. Alternatively use a MultiPlus with built-in transfer switch. CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number PIN122300000 Voltage 12 VA 3000 Peak Power (VA) 6000 Max Efficiency 93% IP Rating IP22 Dimensions (Including Terminals) H533 x W285 x D150mm Weight (kg) 19 Warranty 5 Years

Read more less

All Batteries are Made By Leading Manufacturers The AGM range has very low internal resistance making them particularly suitable for high current discharge applications such as for inverters, thrusters and winches.  VRLA AGM: design life 7-10 years   Features VRLA technology VRLA stands for Valve Regulated Lead Acid, which means that the batteries are sealed. Gas will escape through the safety valves only in case of overcharging or cell failure. VRLA batteries are maintenance free for life. Sealed (VRLA) AGM Batteries AGM stands for Absorbent Glass Mat. In these batteries the electrolyte is absorbed into a glass-fibre mat between the plates by capillary action. As explained in our book ‘Energy Unlimited’, AGM batteries are more suitable for short-time delivery of high currents than gel batteries. Low Self-Discharge Because of the use of lead calcium grids and high purity materials, Victron VRLA batteries can be stored during long periods of time without recharge. The rate of self-discharge is less than 2% per month at 20°C. The self-discharge doubles for every increase in temperature by 10°C. Victron VRLA batteries can therefore be stored for up to a year without recharging, if kept under cool conditions. Exceptional Deep Discharge Recovery Victron VRLA batteries have exceptional discharge recovery, even after deep or prolonged discharge. Nevertheless repeatedly deep and prolonged discharge has a very negative effect on the service life of all lead acid batteries, Victron batteries are no exception. Battery Discharging Characteristics The rated capacity of Victron AGM and Gel Deep Cycle batteries refers to 20 hour discharge, in other words: a discharge current of 0,05 C. The rated capacity of Victron Tubular Plate Long Life batteries refers to 10 hours discharge. The effective capacity decreases with increasing discharge current (see table 1). Please note that the capacity reduction will be even faster in case of a constant power load, such as an inverter.  All Prices Include VAT  Click Here For Spec Sheet Brand Victron Energy Manufacturer Part Number BAT412124081 GTIN 8719076045489 Voltage 12V Battery Capacity (C20) 240Ah Cold Cranking 650CCA Terminal Type M8 Terminal Layout Side Dimensions (Including Terminals) L522 x W240 x H224mm Weight 67Kg Warranty 2 Years Country of Manufacture China Battery Technology AGM Battery Application Dual Purpose      

Read more less

Completely encapsulated: waterproof, shockproof and ignition protected Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.   Extra-long input and output cables Thanks to the cables of 1.8 meters in length, intermediate cable interconnections to increase length even more will in most cases not be needed. This is an important reliability increasing feature in an area were IP67 protection grade is needed.   Wide input voltage range With 15 to 40 Volts input range, a stable output is ensured during surges or sags due to other equipment connected to same battery.   Protected against overheating It can be used in a hot environment such as a machine room. Brand Victron Energy Manufacturer Part Number ORI241220260 GTIN 8719076048442 Voltage 24/12V Cont. Output Current 20A Efficiency 95% Protection Category IP67 Bluetooth Enabled No Dimensions H74 x W74 x D32mm Weight 0.3Kg Warranty 5 Years Country of Manufacture China

Read more less

Remote on-off connector The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual).   All models with adjustable output can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system.   All models with adjustable output can be paralleled to increase output current Up to five units can be connected in parallel.   Easy to install Delivery includes four Insulated Fastons Female Crimp 6.3mm (eight Fastons in case of the Orion 24/12-40).   Low power models: please see Orion-Tr series Brand Victron Energy Manufacturer Part Number ORI241270020 GTIN 8719076023043 Voltage 24/12V Cont. Output Current 70A Protection Category IP20 Efficiency 92% Bluetooth Enabled No Dimensions H65 x W88 x D195mm Weight 0.9Kg Warranty 5 Years Country of Manufacture India

Read more less

High stock levels available on all panels, please contact us via live chat for up-to-date stock before purchase, as stock levels are subject to change. Alternatively, you can email or call us. Low voltage-temperature coefficient enhances high-temperature operation. Exceptional low-light performance and high sensitivity to light across the entire solar spectrum. 25-Year limited warranty on power output and performance. 5-Year limited warranty on materials and workmanship. Sealed, waterproof, multi-functional junction box gives high level of safety. High performance bypass diodes minimize the power drop caused by shade. Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation. A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems. Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance. High power models with pre-wired quick-connect system with MC4 (PV-ST01) connectors.  CLICK HERE FOR SPEC SHEETS Brand Victron Energy Manufacturer Part Number SPM041401200 GTIN 8719076055808 Voltage 12V Nominal Power 140W Cell Type Monocrystalline Number of Cells in Series 36 Maximum System Voltage 1000V Dimensions L1250 x W668 x D30mm Weight 9Kg Warranty 5 Years

Read more less

Lithium-iron-phosphate (LiFePO4 or LFP) is the safest of the mainstream li-ion battery types. The nominal voltage of a LFP cell is 3,2V (lead-acid: 2V/cell). A 12,8V LFP battery therefore consists of 4 cells connected in series; and a 25,6V battery consists of 8 cells connected in series. Features - Rugged A lead-acid battery will fail prematurely due to sulfation:    If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged). If it is left partially charged or worse, fully discharged (yacht or mobile home during wintertime). A LFP battery does not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of LFP compared to lead-acid. Other advantages are the wide operating temperature range, excellent cycling performance, low internal resistance and high efficiency (see below). LFP is therefore the chemistry of choice for demanding applications. Efficient In several applications (especially off-grid solar and/or wind), energy efficiency can be of crucial importance. The round-trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average leadacid battery is 80%. The round-trip energy efficiency of a LFP battery is 92%. The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy is required (battery operating in 70% to 100% charged state). In contrast, a LFP battery will still achieve 90% efficiency under shallow discharge conditions. Size and weight Saves up to 70% in space Saves up to 70% in weight Expensive? LFP batteries are expensive when compared to lead-acid. But in demanding applications, the high initial cost will be more than compensated by longer service life, superior reliability and excellent efficiency. Bluetooth With Bluetooth cell voltages, temperature and alarm status can be monitored. Very useful to localize a (potential) problem, such as cell imbalance. BMS Our LFP batteries have integrated cell balancing and cell monitoring. Up to 5 batteries can be paralleled and up to four 12V batteries or two 24V batteries can be series connected, so that a 48V battery bank of up to 1500Ah can be assembled. The cell balancing/monitoring cables can be daisy-chained and must be connected to a Battery Management System (BMS).  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BAT524120610 Voltage 25.6 Capacity (C20) 200 Terminal Type M8 Terminal Layout LH+ Dimensions (Including Terminals) H237 x W650 x D163mm Weight (kg) 39 Warranty 3 Years Battery Technology Lithium

Read more less

  The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model. Brand Victron Energy Manufacturer Part Number ASS030530203 Cable Length 0.3m Warranty 5 Years

Read more less

The Blue Smart IP22 Charger is the new professional battery charger with built-in bluetooth. The Blue Smart IP22 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans. Features   Bluetooth Smart The Blue Smart IP22 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available.   High efficiency With up to 94% efficiency, these chargers generate up to four times less heat when compared to the industry standard. And once the battery is fully charged, power consumption reduces to 0,5 Watt, some five to ten times better than the industry standard.   Adaptive 6-stage charge algorithm: test – bulk – absorption – recondition – float – storage The Blue Smart Charger features a microprocessor controlled ‘adaptive’ battery management. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used.   Storage Mode: less maintenance and aging when the battery is not in use The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (13,2V for a 12V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure.   Also charges Li-ion (LiFePO4) batteries LiFePO4 batteries are charged with a simple bulk – absorption – float algorithm.   NIGHT and LOW setting When in NIGHT or LOW mode, the output current is reduced to max. 50% of the nominal output and the charger will be totally noiseless. The NIGHT mode automatically ends after 8 hours. The LOW mode can be ended manually.   Protected against overheating Output current will reduce as temperature increases up to 50°C, but the Blue Smart Charger will not fail.   Eleven LEDs for status indication Charge algorithm: TEST / BULK / ABSORPTION / RECONDITION / FLOAT / STORAGE / READY. MODE button to set: NORMAL (14,4V) / HIGH (14,7V) / RECONDITION / LI-ION.   CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BPC241647022 GTIN 8719076052494 Voltage Charger Amps 16A Outputs 1 Efficiency 94% Plug Type UK IP Rating IP22 Dimensions H235 x W108 x D65mm Weight 1.3Kg Warranty 5 Years

Read more less

M8 circular connector Male/Female 3 pole cable 2m (bag of 2) Brand Victron Energy Manufacturer Part Number ASS030560100 Cable Length 1m Warranty 5 Years

Read more less

 Lithium-iron-phosphate (LiFePO4 or LFP) is the safest of the mainstream li-ion battery types. The nominal voltage of a LFP cell is 3,2V (lead-acid: 2V/cell). A 12,8V LFP battery therefore consists of 4 cells connected in series; and a 25,6V battery consists of 8 cells connected in series. Rugged A lead-acid battery will fail prematurely due to sulfation: • If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged). • If it is left partially charged or worse, fully discharged (yacht or mobile home during wintertime). A LFP battery does not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of LFP compared to lead-acid. Other advantages are the wide operating temperature range, excellent cycling performance, low internal resistance and high efficiency (see below). LFP is therefore the chemistry of choice for demanding applications. Efficient In several applications (especially off-grid solar and/or wind), energy efficiency can be of crucial importance. The round-trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average leadacid battery is 80%. The round-trip energy efficiency of a LFP battery is 92%. The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy is required (battery operating in 70% to 100% charged state). In contrast, a LFP battery will still achieve 90% efficiency under shallow discharge conditions. Size and weight Saves up to 70% in space Saves up to 70% in weight Expensive? LFP batteries are expensive when compared to lead-acid. But in demanding applications, the high initial cost will be more than compensated by longer service life, superior reliability and excellent efficiency. Bluetooth With Bluetooth cell voltages, temperature and alarm status can be monitored. Very useful to localize a (potential) problem, such as cell imbalance Our LFP batteries have integrated cell balancing and cell monitoring. Up to 5 batteries can be paralleled and up to four 12V batteries or two 24V batteries can be series connected, so that a 48V battery bank of up to 1500Ah can be assembled. The cell balancing/monitoring cables can be daisy-chained and must be connected to a Battery Management System (BMS). Battery Management System (BMS) The BMS will: 1. Generate a pre-alarm whenever the voltage of a battery cell decreases to less than 3,1V (adjustable 2,85 – 3,15 V). 2. Disconnect or shut down the load whenever the voltage of a battery cell decreases to less than 2,8V (adjustable 2,6 V – 2,8 V). 3. Stop the charging process whenever the voltage of a battery cell increases to more than 3,75 V or the temperature increases to more than 60°C. See the BMS datasheets for more features CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BAT512110610 GTIN 8719076043041 Voltage 12.8V Battery Capacity (C20) 100Ah Terminal Type M8 Terminal Layout Right Hand Positive Dimensions (Including Terminals) H197 x W321 x D152mm Weight 14Kg Warranty 3 Years Country of Manufacture China Battery Technology Lithium Battery Application Deep Cycle

Read more less

The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).  If required, Bluetooth can be disabled. The Smart BatteryProtect is not designed for reverse currents from charging sources.   Features Protects the battery against excessive discharge and can be used as a system on/off switch The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The on/off input can be used as a system on/off switch. 12/24V auto ranging The Smart BatteryProtect automatically detects system voltage one time only. Bluetooth: programming made easy When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled. A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS Ultra-low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information. Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V. Ignition proof No relays but MOSFET switches, and therefore no sparks. Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number BPR065022000 Voltage 12/24 Peak Current (During 30 Seconds) 250A Max. Continuous Load Current 65A Connection M6 IP Rating Electronics: IP67 (potted) Connections: IP00 Dimensions (Including Terminals) H40 x W48 x D106mm Weight (kg) 0.2 Warranty 5 Years

Read more less

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life. The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulphated or otherwise damaged.   Features Remote Monitoring and Control Remotely control and monitor the extensive features of your BlueSolar MPPT charger by attaching a bluetooth dongle and pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet with a GX device, the Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both VictronConnect and VRM are free to use. For remote installations – even when there is no internet connection nearby – you may be able to monitor your MPPT by connecting the GlobalLink 520. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Flexible charge algorithm Fully programmable charge algorithm (see the software page on our website), and eight preprogrammed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more SmartSolar Charge Controllers. Synchronized parallel charging with Bluetooth Up to 10 units can be synchronized with Bluetooth. Fully discharged battery recovery function Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function. VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC115070211 GTIN 8719076051404 Battery Voltage 12/24/48V Auto Select (software tool needed to select 36V) Rated Charge Current 70A Nominal PV Power, 12V 1000W Nominal PV Power, 24V 2000W Max. PV Short Circuit Current 50A Maximum PV Open Circuit Voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Efficiency 98% Charge Algorithm Multi-stage adaptive (eight preprorammed algorithms) or user defined algorithm Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H185 x W250 x D95mm Weight 3Kg Warranty 5 Years

Read more less

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.   MPPT: Ultra Fast Maximum Power Point Tracking By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing. Remote Monitoring and Control Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally. Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers. VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 98%. Full output current up to 40°C (104°F). Flexible charge algorithm Fully programmable charge algorithm (see the software page on our website), and eight preprogrammed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Optional external battery voltage and temperature sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC115035210 GTIN 8719076040187 Battery Voltage 12 / 24 / 48V Auto Select (software tool needed to select 36V) Rated Charge Current 35A Nominal PV Power, 12V 500W Nominal PV Power, 24V 1000W Max. PV Short Circuit Current 40A Maximum PV Open Circuit Voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Efficiency 98% Charge Algorithm Multi-stage adaptive (eight preprorammed algorithms) or user defined algorithm Data Communication Port VE.Direct IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H130 x W186 x D70mm Weight 1.25Kg Warranty 5 Years

Read more less

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life.   Features Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points (MPP) may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 99%. Flexible charge algorithm Fully programmable charge algorithm, and eight preprogrammed algorithms, selectable with a rotary switch (see manual for details). Extensive electronic protection Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection. Internal temperature sensor Compensates absorption and float charge voltage for temperature. Optional external battery voltage, temperature and current sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature (and current, in case of a BMV 712 or a SmartShunt) to one or more BlueSolar Charge Controllers. (VE.Direct Bluetooth Smart dongle needed) VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can VE.Direct or VE.Can For a wired data connection to a Color Control GX, other GX products, PC or other devices Remote on-off To connect for example to a VE.BUS BMS. Programmable relay Can be programmed to trip on an alarm, or other events. Optional: SmartSolar pluggable LCD display Simply remove the rubber seal that protects the plug on the front of the controller, and plug-in the display.  CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number SCC125110441 GTIN 8719076050926 Battery Voltage 12/24/48V Auto Select (36V: manual) Rated Charge Current 100A Nominal PV Power, 12V 1450W Nominal PV Power, 24V 2900W Max. PV Short Circuit Current 70A Maximum PV Open Circuit Voltage 250V absolute maximum coldest conditions | 245V start-up and operating maximum Efficiency 99% Charge Algorithm multi-stage adaptive (eight preprogrammed algorithms) or user defined algorithm Data Communication Port VE.Can IP Rating IP43 (electronic components), IP22 (connection area) Dimensions H216 x W295 x D103mm Weight 4.5Kg Warranty 5 Years

Read more less

The SmartSolar MPPT RS solar charge controllers are Victron’s solution for systems with large series connected PV arrays charging 48 V DC battery banks. This product is perfect for large off-grid, and grid connected battery systems. Available in a 5.76kW and 11.52kW model, features include a wide 80-450 VDC operating solar voltage input, independent tracking inputs, full connectivity, isolated PV connections, display screen, fully programmable battery charging parameters and active cooling. The new metal case design and fully covered electrical connections improve the safety and modernise the presentation in line with the latest suite of Victron products.   Features Ultra-fast Maximum Power Point Tracking (MPPT) Solar Charge Controller The MPPT RS SmartSolar is a 48V Solar charge controller with up to 450VDC PV input and either 100A, or 200A output. It is used in on-grid and off-grid solar applications where maximum battery charging power is required. Setup and monitor with VictronConnect The SmartSolar RS charge controller can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, historical data and trends. Multiple independent MPPT tracking inputs With multiple MPPT trackers, you can optimize your solar panel design for maximum performance for your specific location. Daisy Chain Additional Units The SmartSolar RS charge controller is equipped with VE.Can bus ports. This allows for communication with additional SmartSolar RS & VE.Can MPPT units. The additional units are simply “daisy chained” to each other with an RJ45 cable. When connected to each other, all individual charge controllers, will synchronise their charge stages. They can also send their data, via the same cable, for monitoring to a GX device (such as the Cerbo GX). Isolated PV connections for additional safety Full galvanic isolation between PV and battery connections provide additional overall system safety. Wide MPPT voltage range 80 – 450 VDC PV operating range, with a 120VDC PV startup voltage. Light weight, efficient and quiet Thanks to high frequency technology and a new design this powerful charger weighs only 7.9 kg for the 100A model. In addition to this it has an excellent efficiency, low standby power, and a very quiet operation. Display and Bluetooth The display reads battery, and controller parameters. The parameters can be accessed with a smartphone or other Bluetooth enabled device. In addition, Bluetooth can be used to set up the system and to change settings with VictronConnect. PV Isolation resistance monitoring for peace of mind at higher voltages The MPPT RS continuously monitors the PV array and can detect if there are faults that reduce the isolation of the panels to unsafe levels. VE.Can and VE.Direct port For connection to a GX device for system monitoring, data logging, and remote firmware updates. VE.Can allows for up to 25 units to be connected together in parallel and synchronize their charging. I/O Connections Programmable Relay, temperature sensor, auxiliary, digital input and voltage sensor connections. The remote input can accept the Victron smallBMS, and other BMS with allow-to-charge signal CLICK HERE FOR SPEC SHEET gtin 8719076051886 Brand Victron Energy Manufacturer Part Number SCC145120410 Warranty 5 Years Country of Manufacture India Weight (kg) 13.7Kg Programmable Relay Yes Dimensions H487 x W434 x D146mm Battery Voltage 48 V Rated Charge Current 200 A Max. PV Short Circuit Current 20 A per tracker Charge Algorithm Multi-stage adaptive (adjustable) Battery Temperature Sensor Included Remote on-off Yes Battery-Connection M8 Bolts Protection Category IP21 Start-up voltage 120 V MPPT operating voltage range 80 – 450 V Self-consumption 15 mA Maximum efficiency 96% Programmable Voltage Range Minimum: 36 V, Maximum: 62 V Charge Voltage Absorption’ Default setting: 57,6 V (adjustable) Maximum Charge Power 11,5 kW at 57,6 V Charge Voltage Float Default setting: 55,2 V (adjustable) Maximum DC PV Voltage 450 V Number Of Trackers 4 Max. PV Operational Input Current 18 A per tracker Maximum PV Array Size Per Tracker 7200 Wp (450 V x 20 A) Data Communication VE.Direct port, VE.Can port & Bluetooth Synchronised Parallel Operation Yes, up to 25 units with VE.Can General Purpose Analogue/Digital In Port Yes, 2x

Read more less

  Completely encapsulated: waterproof, shockproof and ignition protected Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.   PLEASE CLICK HERE FOR SPEC SHEET Brand Victron Energy Manufacturer Part Number ORI122421226 Input Voltage Range 10-15VDC Output Voltage 24VDC Output Current 50A Output Rated Power 1200W Protection Category IP67 Dimensions L340 x W127 x D63 mm Weight (kg) 3 Warranty 5 Years

Read more less

    Busbars are used for high current distribution and at the same time they provide connections for batteries and/or DC equipment. Victron offer a number of busbars with different current ratings, and a different number of connection terminals. Each busbar is fitted out with a removable protection cover.  Available models: 150A / 70V – 4 high current connections 150A / 70V – 6 high current connections 250A / 70V – 4 high current connections 600A / 70V – 4 high current connections and 8 low current connections 600A / 70V – 8 high current connections and 8 low current connections  For more technical information and for the busbar dimensions see the datasheet.   Brand Victron Energy Manufacturer Part Number VBB125040010 GTIN 8719076052210 Maximum Current 250A Maximum Voltage 70VDC Terminal Diameter 8mm Terminal Height 17mm Dimensions H48 x W237 x D70mm Weight 0.45Kg Warranty 5 Years

Read more less

Busbars are used for high current distribution and at the same time they provide connections for batteries and/or DC equipment. Victron offer a number of busbars with different current ratings, and a different number of connection terminals. Each busbar is fitted out with a removable protection cover.  Available models: 150A / 70V – 4 high current connections 150A / 70V – 6 high current connections 250A / 70V – 4 high current connections 600A / 70V – 4 high current connections and 8 low current connections 600A / 70V – 8 high current connections and 8 low current connections  For more technical information and for the busbar dimensions see the datasheet.     Brand Victron Energy Manufacturer Part Number VBB115040020 GTIN 8719076052197 Maximum Current 150A Maximum Voltage 70VDC Terminal Diameter 6.35mm Terminal Height 17mm Dimensions H45 x W152.4 x D31.8mm Weight 0.2Kg Warranty 5 Years

Read more less

MEGA-fuse 300A/58V for 48V products (1 pc)   Brand Victron Energy Manufacturer Part Number CIP137300010 Warranty 5 Years Appr. Voltage Drop 80 mV Cold Resistance 0.17

Read more less